Fix broken links in content

per1234 · per1234 · commit f6cd584cca79 · 2024-04-19T05:24:42.000-07:00
diff --git a/content/retired/01.boards/arduino-BT-v1/content.md b/content/retired/01.boards/arduino-BT-v1/content.md
@@ -9,7 +9,7 @@ source: "https://arduino.cc/en/Main/ArduinoBoardBluetoothNew"
 
 ### Overview
 
-The Arduino BT (Bluetooth&reg;) is a microcontroller board based on the ATmega168 ([datasheet](./static/resources/datasheets/Datasheet-ATmega48-88-168-doc2545.pdf)) and the Bluegiga WT11 Bluetooth&reg; module [datasheet](./static/resources/datasheets/WT11_Datasheet.pdf) \[pdf\]). It has 14 digital input/output pins (of which 6 can be used as PWM outputs and one can be used to reset the WT11 module), 6 analog inputs, a 16 MHz crystal oscillator, screw terminals for power, an ICSP header, and a reset button. It contains everything needed to support the microcontroller and can be programmed wirelessly over the Bluetooth&reg; connection. Instructions are available for [getting started with the Arduino BT](//www.arduino.cc/en/Guide/ArduinoBT).
+The Arduino BT (Bluetooth&reg;) is a microcontroller board based on the ATmega168 ([datasheet](/resources/datasheets/Datasheet-ATmega48-88-168-doc2545.pdf)) and the Bluegiga WT11 Bluetooth&reg; module [datasheet](/resources/datasheets/WT11_Datasheet.pdf) \[pdf\]). It has 14 digital input/output pins (of which 6 can be used as PWM outputs and one can be used to reset the WT11 module), 6 analog inputs, a 16 MHz crystal oscillator, screw terminals for power, an ICSP header, and a reset button. It contains everything needed to support the microcontroller and can be programmed wirelessly over the Bluetooth&reg; connection. Instructions are available for [getting started with the Arduino BT](//www.arduino.cc/en/Guide/ArduinoBT).
 
 
 ### Summary
@@ -98,7 +98,7 @@ The maximum length and width of the BT are approximately 3.2 and 2.1 inches resp
 
 ## Arduino BT v1 Initialization Sketch
 
-This sketch is run once on each Arduino BT v1 to initialize the Bluetooth&reg; module before the board is shipped (you shouldn't need to run this code; it's just here for reference). For details on the commands sent to the module, see the [iWrap data sheet](./static/resources/datasheets/UG218.pdf).
+This sketch is run once on each Arduino BT v1 to initialize the Bluetooth&reg; module before the board is shipped (you shouldn't need to run this code; it's just here for reference). For details on the commands sent to the module, see the [iWrap data sheet](/resources/datasheets/UG218.pdf).
 
 ```arduino
 /* BT test 01
diff --git a/content/retired/01.boards/arduino-BT/content.md b/content/retired/01.boards/arduino-BT/content.md
@@ -12,7 +12,7 @@ sku: [A000002]
 
 ### Overview
 
-The Arduino BT is a microcontroller board originally was based on the ATmega168, but now is supplied with the 328P ([datasheet](./static/resources/datasheets/ATmega48A-PA-88A-PA-168A-PA-328-P-DS-DS40002061B.pdf)) and the Bluegiga WT11 Bluetooth&reg; module [datasheet](./static/resources/datasheets/assets/WT11_Datasheet.pdf)). It supports wireless serial communication over Bluetooth&reg; (but is not compatible with Bluetooth&reg; headsets or other audio devices). It has 14 digital input/output pins (of which 6 can be used as PWM outputs and one can be used to reset the WT11 module), 6 analog inputs, a 16 MHz crystal oscillator, screw terminals for power, an ICSP header, and a reset button. It contains everything needed to support the microcontroller and can be programmed wirelessly over the Bluetooth&reg; connection. Instructions are available for [getting started with the Arduino BT](content/retired/06.getting-started-guides/ArduinoBT).
+The Arduino BT is a microcontroller board originally was based on the ATmega168, but now is supplied with the 328P ([datasheet](/resources/datasheets/ATmega48A-PA-88A-PA-168A-PA-328-P-DS-DS40002061B.pdf)) and the Bluegiga WT11 Bluetooth&reg; module [datasheet](/resources/datasheets/WT11_Datasheet.pdf)). It supports wireless serial communication over Bluetooth&reg; (but is not compatible with Bluetooth&reg; headsets or other audio devices). It has 14 digital input/output pins (of which 6 can be used as PWM outputs and one can be used to reset the WT11 module), 6 analog inputs, a 16 MHz crystal oscillator, screw terminals for power, an ICSP header, and a reset button. It contains everything needed to support the microcontroller and can be programmed wirelessly over the Bluetooth&reg; connection. Instructions are available for [getting started with the Arduino BT](content/retired/06.getting-started-guides/ArduinoBT).
 
 ### Summary
 
diff --git a/content/retired/01.boards/arduino-diecimila/content.md b/content/retired/01.boards/arduino-diecimila/content.md
@@ -94,7 +94,7 @@ The ATmega168 also supports I2C (TWI) and SPI communication. The Arduino softwar
 
 The Arduino Diecimila can be programmed with the Arduino software ([download](//www.arduino.cc/en/Main/Software)). For details, see the [reference](//www.arduino.cc/en/Reference/HomePage) and [tutorials](//www.arduino.cc/en/Tutorial/HomePage).
 
-The ATmega168 on the Arduino Diecimila comes preburned with a [bootloader](//www.arduino.cc/en/Tutorial/Bootloader) that allows you to upload new code to it without the use of an external hardware programmer. It communicates using the original STK500 protocol ([reference](./static/resources/datasheets/doc2525.pdf), [C header files](./static/resources/datasheets/avr061.zip)).
+The ATmega168 on the Arduino Diecimila comes preburned with a [bootloader](//www.arduino.cc/en/Tutorial/Bootloader) that allows you to upload new code to it without the use of an external hardware programmer. It communicates using the original STK500 protocol ([reference](/resources/datasheets/doc2525.pdf), [C header files](/resources/datasheets/avr061.zip)).
 
 You can also bypass the bootloader and program the ATmega168 through the ICSP (In-Circuit Serial Programming) header; see [these instructions](//www.arduino.cc/en/Hacking/Programmer) for details.
 
diff --git a/content/retired/01.boards/arduino-duemilanove/content.md b/content/retired/01.boards/arduino-duemilanove/content.md
@@ -87,7 +87,7 @@ The ATmega168 and ATmega328 also support I2C (TWI) and SPI communication. The Ar
 
 The Arduino Duemilanove can be programmed with the Arduino software ([download](//www.arduino.cc/en/Main/Software)). Select "Arduino Diecimila or Duemilanove w/ ATmega168" or "Arduino Duemilanove w/ ATmega328" from the **Tools > Board** menu (according to the microcontroller on your board). For details, see the [reference](//www.arduino.cc/en/Reference/HomePage) and [tutorials](//www.arduino.cc/en/Tutorial/HomePage).
 
-The ATmega168 or ATmega328 on the Arduino Duemilanove comes preburned with a [bootloader](//www.arduino.cc/en/Tutorial/Bootloader) that allows you to upload new code to it without the use of an external hardware programmer. It communicates using the original STK500 protocol ([reference](./static/resources/datasheets/doc2525.pdf), [C header files](./static/resources/datasheets/avr061.zip)).
+The ATmega168 or ATmega328 on the Arduino Duemilanove comes preburned with a [bootloader](//www.arduino.cc/en/Tutorial/Bootloader) that allows you to upload new code to it without the use of an external hardware programmer. It communicates using the original STK500 protocol ([reference](/resources/datasheets/doc2525.pdf), [C header files](/resources/datasheets/avr061.zip)).
 
 You can also bypass the bootloader and program the microcontroller through the ICSP (In-Circuit Serial Programming) header; see [these instructions](https://docs.arduino.cc/hacking/software/Programmer) for details.
 

-Original file line number
+Diff line change
 ### Overview
 -The Arduino BT (Bluetooth®) is a microcontroller board based on the ATmega168 ([datasheet](./static/resources/datasheets/Datasheet-ATmega48-88-168-doc2545.pdf)) and the Bluegiga WT11 Bluetooth® module [datasheet](./static/resources/datasheets/WT11_Datasheet.pdf) \[pdf\]). It has 14 digital input/output pins (of which 6 can be used as PWM outputs and one can be used to reset the WT11 module), 6 analog inputs, a 16 MHz crystal oscillator, screw terminals for power, an ICSP header, and a reset button. It contains everything needed to support the microcontroller and can be programmed wirelessly over the Bluetooth® connection. Instructions are available for [getting started with the Arduino BT](//www.arduino.cc/en/Guide/ArduinoBT).
 +The Arduino BT (Bluetooth®) is a microcontroller board based on the ATmega168 ([datasheet](/resources/datasheets/Datasheet-ATmega48-88-168-doc2545.pdf)) and the Bluegiga WT11 Bluetooth® module [datasheet](/resources/datasheets/WT11_Datasheet.pdf) \[pdf\]). It has 14 digital input/output pins (of which 6 can be used as PWM outputs and one can be used to reset the WT11 module), 6 analog inputs, a 16 MHz crystal oscillator, screw terminals for power, an ICSP header, and a reset button. It contains everything needed to support the microcontroller and can be programmed wirelessly over the Bluetooth® connection. Instructions are available for [getting started with the Arduino BT](//www.arduino.cc/en/Guide/ArduinoBT).
 ### Summary
 ## Arduino BT v1 Initialization Sketch
 -This sketch is run once on each Arduino BT v1 to initialize the Bluetooth® module before the board is shipped (you shouldn't need to run this code; it's just here for reference). For details on the commands sent to the module, see the [iWrap data sheet](./static/resources/datasheets/UG218.pdf).
 +This sketch is run once on each Arduino BT v1 to initialize the Bluetooth® module before the board is shipped (you shouldn't need to run this code; it's just here for reference). For details on the commands sent to the module, see the [iWrap data sheet](/resources/datasheets/UG218.pdf).
 ```arduino
 /* BT test 01