Disable eth phys, wlan and change from X6 to X4 drive for eMMC signals in high-speed mode

Author: MaxPayne86

meta-arduino-bsp/recipes-bsp/device-tree/arduino-device-tree/portenta-x9/arduino_portenta-x9.dts

@@ -190,7 +190,7 @@
 	phy-mode = "rgmii-id";
 	phy-handle = <&ethphy2>;
 	fsl,magic-packet;
-	status = "okay";
+	status = "disabled";
 	phy-reset-gpios = <&gpio3 27 GPIO_ACTIVE_LOW>;
 	phy-reset-duration = <10>; /* [ms] */
 	phy-reset-post-delay = <80>; /* [ms] */
@@ -216,7 +216,7 @@
 	pinctrl-0 = <&pinctrl_eqos>;
 	phy-mode = "rgmii-id";
 	phy-handle = <&ethphy1>;
-	status = "okay";
+	status = "disabled";
 
 	mdio {
 		compatible = "snps,dwmac-mdio";
@@ -491,7 +491,7 @@
 	non-removable;
 	wakeup-source;
 	fsl,sdio-async-interrupt-enabled;
-	status = "okay";
+	status = "disabled";
 
 	wifi_wake_host {
 		compatible = "nxp,wifi-wake-host";
@@ -695,17 +695,17 @@
 	/* need to config the SION for data and cmd pad, refer to ERR052021 */
 	pinctrl_usdhc1_200mhz: usdhc1-200mhzgrp {
 		fsl,pins = <
-			MX93_PAD_SD1_CLK__USDHC1_CLK		0x15fe
-			MX93_PAD_SD1_CMD__USDHC1_CMD		0x400013fe
-			MX93_PAD_SD1_DATA0__USDHC1_DATA0	0x400013fe
-			MX93_PAD_SD1_DATA1__USDHC1_DATA1	0x400013fe
-			MX93_PAD_SD1_DATA2__USDHC1_DATA2	0x400013fe
-			MX93_PAD_SD1_DATA3__USDHC1_DATA3	0x400013fe
-			MX93_PAD_SD1_DATA4__USDHC1_DATA4	0x400013fe
-			MX93_PAD_SD1_DATA5__USDHC1_DATA5	0x400013fe
-			MX93_PAD_SD1_DATA6__USDHC1_DATA6	0x400013fe
-			MX93_PAD_SD1_DATA7__USDHC1_DATA7	0x400013fe
-			MX93_PAD_SD1_STROBE__USDHC1_STROBE	0x15fe
+			MX93_PAD_SD1_CLK__USDHC1_CLK		0x15ce
+			MX93_PAD_SD1_CMD__USDHC1_CMD		0x400013ce
+			MX93_PAD_SD1_DATA0__USDHC1_DATA0	0x400013ce
+			MX93_PAD_SD1_DATA1__USDHC1_DATA1	0x400013ce
+			MX93_PAD_SD1_DATA2__USDHC1_DATA2	0x400013ce
+			MX93_PAD_SD1_DATA3__USDHC1_DATA3	0x400013ce
+			MX93_PAD_SD1_DATA4__USDHC1_DATA4	0x400013ce
+			MX93_PAD_SD1_DATA5__USDHC1_DATA5	0x400013ce
+			MX93_PAD_SD1_DATA6__USDHC1_DATA6	0x400013ce
+			MX93_PAD_SD1_DATA7__USDHC1_DATA7	0x400013ce
+			MX93_PAD_SD1_STROBE__USDHC1_STROBE	0x15ce
 		>;
 	};